Inkbird Solid State Relay 40DA DC SSR Black Heat Sink for PID Thermostat Temperature Controller

The Inkbird HEATSINK combined with the SSR worked well with my temperature controller. The 4 photos indicate an application of controlling temperature with an Inkbird SSR and PID control unit. Basically the unit maintains a set temperature to seedling's on top of a heating mat.

I mounted this on the upper side of my CR10 S5's PSU for my upgraded bed heater. I upgraded the fans in the control box and added a stand that has a raspberry pi and 12v Noctua fan powered by the Pi's USB. The exhaust from the case is never warm and I never notice a spike in my Pi's temps in octoprint.I was weary of fakes, which seem to be everywhere, but this one has worked great for me.

Performed so well, I've ordered 2 set's over the last 8 months. Couldn't imagine using anything else. Definitely worth the money!One big call out is. You may want to research the difference between a ssr-Da and a ssr-AA and finally a low voltage contactor for your application needs. I only say this because it appears from the reviews, that many people are miss matching their ssr to their applications.I know that I did this in the beginning and toasted a few myself... Do the research first, it'll pay off in the long run.

Great product. Just make sure you don’t run too many amps through it.

I built a unit to conrtol the temperature on my tempering oven I use for knife making. My inkbird items all work great. For very little money I was able to take care of the huge varience of temperatures I was having. I purchased an SSR, heat sink and a PID. All work great. Highly reccomend.

If you check a site like Digi-Key you'll find similar solid state relays in the $50 range. On the Inkbird site (you can buy them direct there) inkbird.shop/products/ssr?variant=13851338047551, the price is $5.59 with free shipping! So you have to wonder where they cut corners to sell them for 1/10 the price of a "standard" SSR.The unit I bought seems to function OK, though I've only tested with a 250W load so far, about 2 amps. At that level the voltage drop measured 0.98VAC so it stayed pretty cool (it is attached to its heat sink). I'll be using it to power an oven, 15 amps or so, we'll see how it holds up then.The build quality is so-so. There's RTV oozing out in places, the terminals are uneven (some higher than others), and there's some corrosion on the terminals.The only functional issue I've found is the LED is very dim. At first I thought it wasn't working at all, but it is, barely.So I'm a little nervous about connecting this to a wall socket but I'll make sure to properly fuse my project so if there's a "mishap" I won't burn the house down. Proceed with caution with these, they are cheaply made.

Update:it's been about 3.5yrs since installing these. The bottom one runs the most. Load is constant at about 17.5A when on. Whatever happened, it failed in the ON state and the terminal melted a bit. The enclosure has an 80mm fan for extra cooling. I'm probably going to strip more wire and loop it around the screws for better contact.Original:I have no idea if this device truly has the guts for 40A, but I only need it for a 25A load. Oversized it deliberately based on youtube videos saying SOME sources were under-built knockoffs; can't say either way here since it would take destructive efforts to determine.After being ON for several minutes, the device & heatsink are still under 100F with ambient temp in the mid 60s. 3.3v signal from the controller works fine to switch the devices.

this is a "Solid" relay! lolits been working great on my 3D printer for a few months now.I use to control my 120V bed and it works beautifully. easy to wire doesn't even get warm.the bed is 300x300 750w silicon pad. and I'm not even using the heat sink with that kind of load.