Sovol Resin 3D Printer Flex Building Plate 2 Pack, Spring Steel Flexible Plate and Magnetic Base Platform for ELEGOO Saturn 4, Saturn 3(Ultra), Saturn 2 8K, Saturn 8K 224x129mm

had quite a few print failed as the pull off the build plate so bought this build plate.plates easy to apply and the backing sticks verywell to the plate .you will lose a few mm on over all height of buildthe plate comes of well but is well held on so can be a bit fiddley .best part is the part just pops off the plate with no issues or scrapinggreat product

135 x 80mm Size - Machine: ELEGOO MARS 2 PRODislikes first - Size, I've lost a bit of build size, but that's itOk so it was a little tricky to get the Z-Axis right until I found out the Mars 2 Pro has a sprung build platform so once the screws are loosened you can push it up into the mount (took me 3hours of fiddling with the limit switch and mount before I worked this out).Once the plate was levelled as per the Elegoo instuctions I ran the print that had previously fused all 8 adapters to the supplied OEM build plate and broken each one trying to prize/scrape/smash it off - Printed perfectly and the parts just slid off (actually only held on by resin vacuum.Next up the larger parts, oh no, they are mainly in the bottom of the tank in a compressed mess!!***** You need to increase the exposure time of the base layers!! *****Bumped the exposure up from 45 to 60 seconds on Elegoo Standard Black and ran again - PERFECTI don't even need to remove the build plate each time to get them off, I leave it in the machine.I've done a litre of Resin in 3 days....................5 Stars

I had massive problems removing models from my original build plate. Anycubic mono x does a too good of a job getting things to stick to the build plate. I broke far too many prints removing them. This upgrade is/was essential for me.Easy to use (if you follow instructions & take your time it works perfectly). The magnetic plates work well and do a very good job. Its handy to have a 2nd plate so you can get another print going while you clean the used plate. I have used these plates over a dozen times and they are as good as new.Great product & very happy with my purchase.

This magnetic build plate works. It does the job and is suitable for the Elegoo Mars 3 Pro. HOWEVER, there are a few steps that aren't mentioned in the installation guide that you need to take in order to get it working 100%.Right off the bat, your printer will have a hard time homing because the switch that is triggered on homing is now higher up because the build plate is now thicker. You will need to print a shim (look for "magnetic build plate shim" on Printables/Thingiverse) and fit it in order for the printer to be configured correctly.The only other issue I had only showed up when attempting to print a full plate. Prints were falling off the build plate about 1cm up the print. I narrowed the problem down to the smooth surfaces of the removeable plate. The instructions say that one side is more textured that the other one so that you can choose this side if there are adhesion problems. However, both of the plates I received seemed to be exactly the same on both sides. This wasn't much of an issue that a bit of sanding cant solve but it was a tad annoying to have wasted a fair bit of resin finding this out.All in all, for the price its not bad but you do appear to get what you pay for.

Photon Mono 4K. Z limit spacer installed, plate installed according to instructions. Relevelled and zeroed. No problems. The second I print, it tries to push through the screen. This occurs seemingly at random and sometimes immediately after relevelling.When it isn't pushing through the screen I'm getting print failures in the same left to right fashion each time. These failures do not occur on a stock build plate and do occur on both of the products I recieved. Both were sanded to improve adhesion, they both still failed.My issues occur with this plate specifically.I'd ask for my money back but in order to discover the product was naff, I had to use it.